FFCONFIG.TXT

#************************************************
# ff_sys_config.ini
# Fodder Factory Monitoring and Control
#
# (c) Brendan McLearie - bmclearie@mclearie.com
#
# System configuration settings as an ini file:
# 	System configuration
# 	Input Configs
# 	Monitor Configs
#	Schedule Configs
#   Rule Configs
#	Controller Configs
# 	Output Configs
#************************************************/


#************************************************
# System
#************************************************/
[system]
type = SYS_SYSTEM
display_name = System
description = Reserved System Block
language = English
temp_scale = Celsius
#temp_scale = Fahrenheit
week_start = SUN
		
#************************************************
# Inputs
#************************************************/
[inputs]
input1 = IN_TOP_TEMP
input2 = IN_BOT_TEMP
input3 = IN_OUT_TEMP
#input4 = IN_WATER_TEMP
input4 = IN_CAB_TEMP
input5 = IN_TANK_TEMP

[IN_TOP_TEMP]
type = IN_ONEWIRE
display_name = Inside Top
description = Dallas sensor top of box
interface = ONEWIRE
if_num = 0
log_rate = 00:02:00
data_units = Celsius
data_type = float

[IN_BOT_TEMP]
type = IN_ONEWIRE
display_name = Inside Bottom
description = Dallas sensor bottom of box
interface = ONEWIRE
if_num = 1
log_rate = 00:02:00
data_units = Celsius
data_type = float

[IN_CAB_TEMP]
type = IN_ONEWIRE
display_name = Cabinet
description = Dallas sensor elec cabinet
interface = ONEWIRE
if_num = 2
log_rate = 00:02:00
data_units = Celsius
data_type = float

[IN_OUT_TEMP]
type = IN_ONEWIRE
display_name = Outside
description = Dallas sensor outside air
interface = ONEWIRE
if_num = 3
log_rate = 00:02:00
data_units = Celsius
data_type = float

[IN_TANK_TEMP]
type = IN_ONEWIRE
display_name = Main Tank
description = Dallas sensor main water tank
interface = ONEWIRE
if_num = 4
log_rate = 00:02:00
data_units = Celsius
data_type = float

#[IN_WATER_TEMP]
#type = IN_ONEWIRE
#display_name = Header Water
#description = Dallas sensor header tank
#interface = ONEWIRE
#if_num = 2
#log_rate = 00:02:00
#data_units = Celsius
#data_type = float


#************************************************
# Monitors
#************************************************/
[monitors]
monitor1 = MON_TOP_COLD
monitor2 = MON_TOP_HOT
monitor3 = MON_BOT_COLD
monitor4 = MON_BOT_HOT
monitor5 = MON_BOT_VERY_COLD
monitor6 = MON_OUT_VERY_COLD
monitor7 = MON_OUT_WARM

[MON_TOP_COLD]
type = MON_CONDITION_LOW
display_name = Inside Top Too Cold
description =  
input1 = IN_TOP_TEMP
act_val	= 18.00
deact_val = 19.00

[MON_TOP_HOT]
type = MON_CONDITION_HIGH
display_name = Inside Top Too Hot
description = 
input1 = IN_TOP_TEMP
act_val	= 21.60
deact_val = 20.60

[MON_BOT_COLD]
type = MON_CONDITION_LOW
display_name = Inside Bottom Too Cold
description =  
input1 = IN_BOT_TEMP
act_val	= 18.00
deact_val = 20.60

[MON_BOT_HOT]
type = MON_CONDITION_HIGH
display_name = Inside Bottom Too Hot
description = 
input1 = IN_BOT_TEMP
act_val	= 21.60
deact_val = 20.60

[MON_BOT_VERY_COLD]
type = MON_CONDITION_LOW
display_name = Bottom Very Cold
description = Bottom Temprature Very Cold
input1 = IN_BOT_TEMP
act_val	= 16.00
deact_val = 18.00

[MON_OUT_VERY_COLD]
type = MON_CONDITION_LOW
display_name = Outside Cold
description = Outside Temprature Very Cold
input1 = IN_OUT_TEMP
act_val	= 16.00
deact_val = 18.00

[MON_OUT_WARM]
type = MON_CONDITION_HIGH
display_name = Outside HOT
description = Outside Temprature Hot
input1 = IN_OUT_TEMP
act_val = 21.00
deact_val = 20.90

#************************************************
# Schedules
#************************************************/
[schedules]
schedule1 = SCH_LIGHTS
schedule2 = SCH_WATER_TOP
schedule3 = SCH_WATER_BOT
schedule4 = SCH_WATER_TOP_COLD
schedule5 = SCH_WATER_BOT_COLD

[SCH_LIGHTS]
type = SCH_START_STOP
display_name = Run Lights at Night
description = 
# ALL, MON, TUE, WED, THU, FRI, SAT, SUN
days = ALL
time_start = 01:00:00
time_end = 07:00:00

[SCH_WATER_TOP]
type = SCH_START_DURATION_REPEAT
display_name = Watering Schedule Top Spray
description = 
# ALL, MON, TUE, WED, THU, FRI, SAT, SUN
days = ALL
time_start = 00:00:00
time_duration = 00:00:15
time_repeat = 00:45:00

[SCH_WATER_BOT]
type = SCH_START_DURATION_REPEAT
display_name = Watering Schedule Bottom Spray
description = 
# ALL, MON, TUE, WED, THU, FRI, SAT, SUN
days = ALL
time_start = 00:00:30
time_duration = 00:00:20
time_repeat = 00:45:00

[SCH_WATER_TOP_COLD]
type = SCH_START_DURATION_REPEAT
display_name = Watering Schedule Top Sprinklers
description = 
# ALL, MON, TUE, WED, THU, FRI, SAT, SUN
days = ALL
time_start = 00:00:00
time_duration = 00:00:20
time_repeat = 00:10:00

[SCH_WATER_BOT_COLD]
type = SCH_START_DURATION_REPEAT
display_name = Watering Schedule Bottom Sprinklers
description = 
# ALL, MON, TUE, WED, THU, FRI, SAT, SUN
days = ALL
time_start = 00:01:00
time_duration = 00:00:30
time_repeat = 00:10:00

#************************************************
# Rules
#************************************************/
[rules]
rule1 = RL_LIGHTS
rule2 = RL_COLD_FAN
rule3 = RL_CIRC_FAN 
rule4 = RL_EXH_FAN
rule5 = RL_COLD_WATER_TOP
rule6 = RL_COLD_WATER_BOT
rule7 = RL_WATER_TOP
rule8 = RL_WATER_BOT
rule9 = RL_BOOST
rule10 = RL_TOP_BOOST
rule11 = RL_BOT_BOOST

[RL_LIGHTS]
type = RL_LOGIC_SINGLE
display_name = Lights on Schedule
description = Operate Lights According to Schedule
param1 = SCH_LIGHTS
#param_not = 

[RL_COLD_FAN]
type = RL_LOGIC_ANDNOT
display_name = Cold Fan Rule
description = Cold Fan Top Hot Out Hot Bot not Cold
param1 = MON_TOP_HOT
param2 = MON_OUT_WARM
param_not = MON_BOT_COLD

[RL_CIRC_FAN]
type = RL_LOGIC_AND
display_name = Circulate Rule
description = Circulate Top Hot and Bot Cold
param1 = MON_TOP_HOT
param2 = MON_BOT_COLD
#param_not = 

[RL_EXH_FAN]
# Change when COLD_FAN actually installed
type = RL_LOGIC_SINGLENOT
display_name = Exhaust Fan Rule
description = Exhaust Top Hot and Bot Not Cold
param1 = MON_TOP_HOT
#param2 = 
param_not = MON_BOT_COLD

[RL_COLD_WATER_TOP]
type = RL_LOGIC_ANDNOT
display_name = Cold Water Selected
description =
param1 = SCH_WATER_TOP
param2 = MON_OUT_WARM
param_not = MON_BOT_COLD

[RL_COLD_WATER_BOT]
type = RL_LOGIC_ANDNOT
display_name = Cold Water Selected
description =
param1 = SCH_WATER_BOT
param2 = MON_OUT_WARM
param_not = MON_BOT_COLD

[RL_WATER_TOP]
type = RL_LOGIC_SINGLENOT
display_name = Water Cycle Top
description =
param1 = SCH_WATER_TOP
param_not = RL_TOP_BOOST

[RL_WATER_BOT]
type = RL_LOGIC_SINGLENOT
display_name = Water Cycle Bottom
description =
param1 = SCH_WATER_BOT
param_not = RL_BOT_BOOST

[RL_BOOST]
type = RL_LOGIC_AND
display_name = Cold Bottom and Out Boost
description =
param1 = MON_BOT_VERY_COLD
param2 = MON_OUT_VERY_COLD
#param_not = 

[RL_TOP_BOOST]
type = RL_LOGIC_AND
display_name = Water Boost Top
description =
param1 = SCH_WATER_TOP_COLD
param2 = RL_BOOST
#param_not = 

[RL_BOT_BOOST]
type = RL_LOGIC_AND
display_name = Water Boost Bottom
description =
param1 = SCH_WATER_BOT_COLD
param2 = RL_BOOST
#param_not = 

#************************************************
# Controllers
#************************************************/
[controllers]
controller1 = CON_LIGHTS
controller2 = CON_COLD_FAN
controller3 = CON_CIRC_FAN
controller4 = CON_EXH_FAN
controller5 = CON_COLD_WATER_TOP
controller6 = CON_COLD_WATER_BOT
controller7 = CON_WATER_TOP
controller8 = CON_WATER_BOT
controller9 = CON_TOP_BOOST
controller10 = CON_BOT_BOOST

[CON_LIGHTS]
type = CON_ONOFF
display_name = End Lights Controller
description = 
rule = RL_LIGHTS
output = OUT_LIGHTS
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_COLD_FAN]
type = CON_ONOFF
display_name = Circulation Fan Controller
description = 
rule = RL_COLD_FAN
output = OUT_COLD_FAN
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_CIRC_FAN]
type = CON_ONOFF
display_name = Circulation Fan Controller
description = 
rule = RL_CIRC_FAN
output = OUT_CIRC_FAN
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_EXH_FAN]
type = CON_ONOFF
display_name = Exhaust Fan Controller
description = 
rule = RL_EXH_FAN
output = OUT_EXH_FAN
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_COLD_WATER_TOP]
type = CON_ONOFF
display_name = Cold Water Solenoid Controller
description = 
rule = RL_COLD_WATER_TOP
output = OUT_COLD_WATER
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_COLD_WATER_BOT]
type = CON_ONOFF
display_name = Cold Water Solenoid Controller
description = 
rule = RL_COLD_WATER_BOT
output = OUT_COLD_WATER
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_WATER_TOP]
type = CON_ONOFF
display_name = Top Spray Solenoid Controller
description = 
rule = RL_WATER_TOP
output = OUT_WATER_TOP
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_WATER_BOT]
type = CON_ONOFF
display_name = Bottom Spray Solenoid Controller
description = 
rule = RL_WATER_BOT
output = OUT_WATER_BOT
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_TOP_BOOST]
type = CON_ONOFF
display_name = Top Spray Solenoid Controller
description = 
rule = RL_TOP_BOOST
output = OUT_WATER_TOP
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF

[CON_BOT_BOOST]
type = CON_ONOFF
display_name = Bottom Spray Solenoid Controller
description = 
rule = RL_BOT_BOOST
output = OUT_WATER_BOT
act_cmd = CMD_OUTPUT_ON
deact_cmd = CMD_OUTPUT_OFF


#************************************************
# Outputs
#************************************************
[outputs]
output1 = OUT_LIGHTS
output2 = OUT_WATER_HEAT
output3 = OUT_COLD_FAN
output4 = OUT_CIRC_FAN
output5 = OUT_EXH_FAN
output6 = OUT_COLD_WATER
output7 = OUT_WATER_TOP
output8 = OUT_WATER_BOT

#PINS 8  7  6  4  4  3  2  1
#PINS 1  2  3  4  5  6  7  8
#PINS 22 24 26 28 30 32 34 36
#PINS LT WH CF IF EF CW S1 S2 

[OUT_LIGHTS]
type = OUT_DIGITAL
display_name = Fluro Lights
description = Relay to Control Fluro End Lights
interface = DIG_PIN_OUT
if_num = 22

[OUT_WATER_HEAT]
type = OUT_DIGITAL
display_name = Header Tank Heater
description = Relay to Header Tank Water Heater
interface = DIG_PIN_OUT
if_num = 24

[OUT_COLD_FAN]
type = OUT_DIGITAL
display_name = Cold Air Fan
description = Relay Cold Air Fan
interface = DIG_PIN_OUT
if_num = 26

[OUT_CIRC_FAN]
type = OUT_DIGITAL
display_name = Circulation Fan
description = Relay Circulation Fan
interface = DIG_PIN_OUT
if_num = 28

[OUT_EXH_FAN]
type = OUT_DIGITAL
display_name = Exhaust Fan
description = Relay to Control the Exhaust Fan
interface = DIG_PIN_OUT
if_num = 30

[OUT_COLD_WATER]
type = OUT_DIGITAL
display_name = Cold Water Value
description = Relay Cold Water Solenoid
interface = DIG_PIN_OUT
if_num = 32

[OUT_WATER_TOP]
type = OUT_DIGITAL
display_name = Water Value Top
description = Relay Top Watering Solenoid
interface = DIG_PIN_OUT
if_num = 34

[OUT_WATER_BOT]
type = OUT_DIGITAL
display_name = Water Value Bottom
description = Relay Bottom Watering Solenoid
interface = DIG_PIN_OUT
if_num = 36