Hi,
I'm total new here, so at first "Hello"!!!!
I updated my Neptune 4 PLUS last weekend from latest stock firmware to v0.1.7-ZNP-K1-25.11.0-edge-6.16.12.
since that I noticed all leveling jobs are out from center
the screw tilt adjust does not hit on coordinats of the screws.
so I searched and found the bed level coordinates in printer.cfg
original:
screw1: 189.25,204.55 screw1_name: middle-rear bed mount (shim adjust) screw2: 189.25,86.55 screw2_name: middle-front bed mount (shim adjust) screw3: 59.75,277.05 screw3_name: rear left screw screw4: 59.75,144.55 screw4_name: center left screw screw5: 59.75,12.05 screw5_name: front left screw screw6: 315.75,12.05 screw6_name: front right screw screw7: 315.75,144.55 screw7_name: center right screw screw8: 315.75,277.05 screw8_name: rear right screw horizontal_move_z: 5 speed: 150 screw_thread: CW-M4
the Neptune 4 plus have a printing pad of 330 to 330 mm (12,99 to 12,99 inch)
the middle will be somewhere about 160mm (look above, meddle screws at near 190mm makes no sense)
so i measured the new coordinates and after some fine-tuning i have new coordinates for my Neptune 4 PLUS
[screws_tilt_adjust] screw1: 164.30,223.00 screw1_name: middle-rear bed mount (shim adjust) screw2: 164.30,104.00 screw2_name: middle-front bed mount (shim adjust) screw3: 37.60,295.70 screw3_name: rear left screw screw4: 37.60,163.00 screw4_name: center left screw screw5: 37.60,31.00 screw5_name: front left screw screw6: 291.00,31.00 screw6_name: front right screw screw7: 291.00,163.00 screw7_name: center right screw screw8: 291.00,295.70 screw8_name: rear right screw horizontal_move_z: 5 speed: 150 screw_thread: CW-M4
now screw leveling is right above the screws and works perfekt
Can anyone confirm the coordinats or why are mine so far away from stock?
next question is full bed leveling:
where can I tune this coordinates? These are also out of center.
Kind regards
Chris
Hi,
I'm total new here, so at first "Hello"!!!!
I updated my Neptune 4 PLUS last weekend from latest stock firmware to v0.1.7-ZNP-K1-25.11.0-edge-6.16.12.
since that I noticed all leveling jobs are out from center
the screw tilt adjust does not hit on coordinats of the screws.
so I searched and found the bed level coordinates in printer.cfg
original:
screw1: 189.25,204.55 screw1_name: middle-rear bed mount (shim adjust) screw2: 189.25,86.55 screw2_name: middle-front bed mount (shim adjust) screw3: 59.75,277.05 screw3_name: rear left screw screw4: 59.75,144.55 screw4_name: center left screw screw5: 59.75,12.05 screw5_name: front left screw screw6: 315.75,12.05 screw6_name: front right screw screw7: 315.75,144.55 screw7_name: center right screw screw8: 315.75,277.05 screw8_name: rear right screw horizontal_move_z: 5 speed: 150 screw_thread: CW-M4the Neptune 4 plus have a printing pad of 330 to 330 mm (12,99 to 12,99 inch)
the middle will be somewhere about 160mm (look above, meddle screws at near 190mm makes no sense)
so i measured the new coordinates and after some fine-tuning i have new coordinates for my Neptune 4 PLUS
[screws_tilt_adjust] screw1: 164.30,223.00 screw1_name: middle-rear bed mount (shim adjust) screw2: 164.30,104.00 screw2_name: middle-front bed mount (shim adjust) screw3: 37.60,295.70 screw3_name: rear left screw screw4: 37.60,163.00 screw4_name: center left screw screw5: 37.60,31.00 screw5_name: front left screw screw6: 291.00,31.00 screw6_name: front right screw screw7: 291.00,163.00 screw7_name: center right screw screw8: 291.00,295.70 screw8_name: rear right screw horizontal_move_z: 5 speed: 150 screw_thread: CW-M4now screw leveling is right above the screws and works perfekt
Can anyone confirm the coordinats or why are mine so far away from stock?
next question is full bed leveling:
where can I tune this coordinates? These are also out of center.
Kind regards
Chris